Mark I. Rosen – Publications
Magazine Articles
“Guidelines For Part & Tool Design For Molding Rigid Clear Materials”, SPE Plastics Engineering Magazine, June 2016
“The Role of Plastics Compounding for Injection Molding”, SPE Plastics Engineering Magazine, January 2016
“Good Venting”, SPE Plastics Engineering Magazine, June 2015
“Plastics Filling Simulation Software: A 30-Year Journey”, SPE Plastics Engineering Magazine, February 2015
“Injection Molding Trials Gone Bad”, SPE Plastics Engineering Magazine, July/August 2014
“Cellulose-Reinforced Polypropylene: A Processing Study”, SPE Plastics Engineering Magazine, March 2014
“Plastics Project Management: Saving Money In The Wrong Places”, SPE Plastics Engineering Magazine, September/October 2013
“Plastics Project Management: Mistakes To Avoid”, SPE Plastics Engineering Magazine, July/August 2013
(Mentioned) “Diagnosing and Solving Molding Problems – Always a Challenge”, Plastics Engineering Magazine, March 2013, page 41
“Filling Analyst Series” – Injection Molding Magazine (IMM)
“Filling Trough a Living Hinge”, Injection Molding Magazine, Vol. 3. No. 1 January, 1995, pp. 52-53
“Reducing Thermoset Warpage”, Injection Molding Magazine, Vol. 3. No. 2 February, 1995, pp. 62-63
“Avoiding Sinks and Stress”, Injection Molding Magazine, Vol. 3. No. 3. March, 1995, pp. 62-64
“Balancing a Family Mold”, Injection Molding Magazine, Vol. 3. No. 4. April, 1995, pp. 70-71
“Goal: Reduce Production Costs”, Injection Molding Magazine, Vol. 3. No.5. April, 1995, pp. 70-71
“Eliminating Warps and Burns”, Injection Molding Magazine, Vol. 3. No. 6. May, 1995, pp. 70-71
“Gas Traps and Warpage”, Injection Molding Magazine, Vol. 3. No. 7. July, 1995, pp. 48-49
“How Many Gates”, Injection Molding Magazine, Vol. 3. No. 8. August, 1995, pp. 74-75
“Gas Traps Caused by Racetracking”, Injection Molding Magazine, Vol. 3. No. 9. Sept., 1995, pp. 74-75
“Correcting an Out-of-Balance Family Mold”, Injection Molding Magazine, Vol. 3. No. 10. October, 1995, pp. 66-67
“Analyzing a New Mold for Rubber”, Injection Molding Magazine, Vol. 3. No.11. Nov., 1995, pp. 78-79
“Balancing Runners”, Injection Molding Magazine, Vol. 3. No. 12. December., 1995, pp. 68-70
Technical Conferences /Training Classes
Introduction to Polymer Classification Systems, Material Selection for Performance and Value, RETEC, 1986, Hartford Connecticut, pp. 1-32
Improving Profits and Part Quality Trough the Use of New Plastics Flow Analysis Software, Society of Plastics Engineers, Annual Technical Conference (ANTEC) Boston MA, Vol. 111, May 7-11 1995
Current Trends in Mold Filling Analysis, Speaker, Two Day Conference sponsored by Stevens Technology Institute and New Jersey Polymer Extension Center, September 1997
Plastics Design Optimization Training Class, Instructor, Sponsored by New Jersey Polymer Extension Center, 1997
Instructor , RAPRA ltd. Fillcalc Filling Analysis Software - North America 1994- 1998]
Industry Research (Confidential Projects Are Not Listed)
A Study of the Parameters Which Influence the Quality of Parts Produced by Injection Molding, Research Sponsored by Rubbermaid Corporation Jointly with University of Massachusetts, Plastics
Outline of Monitoring Systems: Objectives, Hardware and Tests, Research Sponsored by Rubbermaid Corporation Jointly with University of Massachusetts, Plastics